Today I will discuss How To Fix A Snapped Fishing rod? Fishing is fun! As such it contains incredible opportunities to get closer to nature. Nature, the best friend you can have for good health, good eyesight, good air, connecting to the mixture of green and blue environment.
Despite the weather, as a fact, fishing is a fun adventure and a delightful way to spend quality time in nature. Oh, and also of course catch some fish. So when you’re all set and plan an outing with your family or friends on spending a quality day fishing.
However, before you go fishing, just for caution or to gather the needed kinds of stuff for your outing, why not arrange them, yeah? But what happens when you find your fishing rod repair near me or broken in your storage? Don’t know anyone who can fix it? Or, not getting enough time? It’s okay, today we’ll share the guide how to fix a fishing rod step by step, here.
Let’s try and fix it yourself…
How To Fix A Snapped Fishing Rod Step By Step Guide
01.Mending a Snapped Fiberglas Rod
Sand down or reduce the damaged ends of the rod repair in order that they’re without difficulty flushed up. Jagged edges are weaker, much more likely to interrupt once more than the flush edges with one another. Measure the circumference of the rod. Write down the measurements to without difficulty remember.
Cut a piece of fiberglass pole, about 12 inches long. You can buy fiberglass poles. If the fishing rod repairs near me isn’t hollow, using a fiberglass pole won’t work.
Now slide the fiberglass pole into one side of the rod, then apply a two-part epoxy to the exposed side. Slide the other part and let it dry.
02.Replacing a Rod Guide
Cut off the tape or thread across the damaged manual with a blade. Sand the rod and the brand-new brand new manual to get higher adhesion. Now tape the brand new manual onto the rod and align. To maintain it in place, wrap the foot of the manual with thread. Now place a looped piece of thread over the wrap when there’s 1/8 inch left. Wrap the final half over the second piece of thread.
To pull it tight, feed the thread through the looped piece. Paint two-part epoxy onto the thread and dry it.
03.Changing a Rod Tip
First, heat the tip-top of the fishing rod, loosen the adhesive, and remove any shards. Cut portions of rod cement into strips, match them within the new tip pinnacle. Melt the rod cement within the tip-pinnacle. Slide the tip-pinnacle lipgloss onto the rod so it’s covered up with the guides. Let it dry earlier than you operate it.
Modern Fishing rods don’t wreck effortlessly, however they may be constant effortlessly with easy hints when you have the equipment at home.
Fishing Rod Repair: How to Repair a Broken Fishing Rod
“Just but a new one” but that doesn’t mean it’s the best way to go. Apply this guide before you decide to throw your fishing rod repair:
01.Gather Everything Together
To repair your broken fishing rod properly, you need:
- 15-minute epoxy
- And the old rod of similar size
- A two-part coating like Flexcoat
- Rod winding thread
Take out good enough time for the repairing. An important fact, when you’re epoxying the rod, you can’t leave between the procedures since that would hurt your result.
02.Identify The Damages
With everything gathered you need for fixing. Take a better look at the break. Find out, what exactly is the break? Where did the rod snap? What kind of break it is? Is the broken part is crushed or shattered?
If you see the crack is right on the blank and not near any guide, then that will make the process easier to manage. Because you won’t have to remove anything to get the task done.
If you find the break is clean and smooth, it will be easier to manage. Since you won’t need that long of an insert to take the pressure off the blank
Or, if you see the broken part is crushed or shattered, it will need a much longer insert and more attention with the epoxy.
03.Prepare Your Insert
First, measure the broken piece of rod. You need to determine how long of an insert you would need to create with the old rod. Set a goal of at least six inches of the insert on both sides of the broken rod.
Second, sand down the damaged area of the rod until they are smooth, to get an accurate measurement. Let’s put the two broken sections together. Measure the six inches out on both sides so that you can dictate how much of an insert you need.
While measuring, check that if the inserting rod is slightly too big, then the two pieces will not sit flush up against each other.
Later, use a piece of the blank that is slightly smaller than the area before inserting it and put it in to test it. Inspect if the inserting portion moves more than a little bit. If so, then you need to increase the size of the blank piece.
04.Epoxy The Two Pieces Together
Once everything is in place and set up and it all fits together nicely. You can epoxy the two pieces together now. Coat the insert generously in the epoxy, and gradually start sliding it into one section of the broken rod. Now push it in until it covers the entire broken part, then slide the other half of the broken rod similarly over the insert until it’s thoroughly flush with the bottom piece.
Clean up the extra epoxy from the break. And set up the rod vertically. Now make sure that the epoxy rests appropriately. Leave the rod-like that for at least two hours. And clean everything finely before the epoxy sets.
05.Wrapping The Area
After the waiting, hours are over and everything looks good. You can proceed to wrap the area with the red thread. You can wrap it as tightly as possible while holding the thread taut throughout the entire procedure. Wrap four inches out from the break on both sides.
You can find the different sizes of thread, which range from ‘A’ to ‘E’. You don’t have to choose particularly of the two. But we would recommend using something in the middle. As long as you can pull it nice and tight.
06.Apply The Flexcoat
Once the rod is wrapped up properly, apply the Flexcoat while turning the rod. It would be easy too if you have a rotisserie. If not, then get someone to stand and rotate the rod for you while you apply the coat. This can work too!
Let’s cover the wrapped area entirely and nicely with the Flexcoat. Continue turning it for a few minutes even after you’re done applying, just to make sure there are no runs. It’s okay if there are some light runs. The rod would still have the necessary strength it needs to perform.
Fishing Rod Guide Repair
Guides are an equal and incredibly important part. Well, they help you properly cast and pull back the line without getting tangled and out of order. If there’ even one guide missing, it will cause you to have too much drag, and resulting in snapped lines and fish loss.
Fixing a guide is simple!
Usually, guides are held on with epoxy. All you have to do is heat the broken guide with a lighter or a candle to break the seal. See, even the necessary stuff can be found in the home.
When the guide gets nice and hot, you would see it start breaking away from the blank, and then you can cut it off with a blade. Be careful not to cut or damage the blank. It might be a bit soft after the heat.
Now when you have completely removed the guide, clean the area with alcohol to remove any old epoxy or grime that might be under the seal.
Take the new guide and use a thin thread wrap. That should be the thinnest wrap you can use.
Now, wrap the thread around the guide and the rod tightly. Seal the new guide onto the blank using a coat of epoxy. Now just let it sit for at least two hours before moving the repairing fishing rods. Give it 24 hours to dry and firm before you take the rod in the water.
You can use rough grit sandpaper to take off extra epoxy.
Fishing Rod Repair Kit
If the tip of your rod is broken and inserted it can’t be built like you could for the rod blank. You have to glue it back on, using a ferrule. A ferrule is a piece that goes over the top to join the two pieces together just like a bandage.
You need to cut the tip with large scissors or clippers to make sure you have a nice and clean break. sand down the edges so it sits nicely against the new tip.
Now you have to put some hot glue inside the ferrule of the new tip and slide it over the sanded broken area. Make sure to use enough glue that it drips from the broken area. This will help secure to create an excellent seal. Later you can wipe off the excess.
Alright, we’re so close to the finishing. Now what you have to do is, hold the two pieces in place until the glue sets and store the rod vertically. Let it dry appropriately.
Again, when everything is dry, you can sand off any excess glue.
See more about How to replace fishing rod guide insert
Fishing Rod Handle Repair
Let’s simply put this. This can be done easily and quickly by using the supplies e have already discussed previously.
If your rod handle is cork, gotta sand it down ‘till it’s smooth, then drill a hole in each section. Let’s take a small wooden dowel, insert it into the cork. Now coat the dowel with hot glue and insert.
Following, take the new section, slide it over the dowel leaving about an inch open. Coat the opening with glue then push the two together, this will create an excellent seal.
Let it sit for a few hours before moving it. If there’s any leftover glue, sand it off.
Tips:
Fishing is about getting out of the daily activity and being in nature.
- If you have trouble fixing the rod on your own, take it to a fishing supply store or a person.
- In an emergency, overlap the pieces by 6 inches and tape them together tightly.
- You can also cut a section of an old fishing pole that you don’t use anymore if you lack a fiberglass rod
- If you want to blend in, use a thread that matches the color of the rod
- If sandpaper isn’t enough to remove the shards, use a pair of scissors carefully.
- Use a diameter if you don’t have a flexible measuring tape.
- Use 180- or 220- grit sandpaper.
Warnings:
Be aware of the situations that may create. So for cautions, remember these warnings.
- Do not hold a flame against the rod longer than a few seconds, or that could permanently damage the rod
- Be careful with using razor blades. Don’t accidentally hurt yourself.
How To Fix A Snapped Fishing Rod (FAQ)
01. Where do I buy epoxy resin glue?
At any home improvement or hardware store.
02. How often should I change my fishing line?
All you need to do is check your fishing line for wear and tear and change it at the right time, which should be at least once a year.
03. What should I do if the glue is not sticking?
Well, if you’re using old glue, in that case, dear, you need to stock a new one or change the type of glue you’re using.
Final thought
Finally, we learned that How To Fix A Snapped Fishing Rod. It’s a stress reducer. When fishing, there can be lots of mistakes, errors on the fishing gear, and whatnot. The most common gloss thing to happen is the tangling of the fishing line. Another disappointing fact is a bad cast. So it’s better to be prepared.
That is why lots suggest target practice at home. Since now you’re practicing at home and you found your fishing rod snapped or maybe broken, you can fix it at home too. All by yourself, no need to go to stores or buy a new one. This way it’s much cheaper and affordable, plus a new skill learned. Just follow the instructions guided above then go fishing.
We hope our simple guides helped you through. Enjoy your fishing dear!
3 thoughts on “Best Guide: How To Fix A Snapped Fishing Rod 2022”